Ecotech-marine Gen 2 MP40 Bedienungsanleitung PDF herunterladen

To remove the nozzle from the wet frame, remove the entire wet half of the pump from the aquarium and

place it on a non-metallic surface. Gently but firmly press down on the nozzle with your palm and twist coun-

ter clockwise. The nozzle should become free of the wet frame. It may then be cleaned of any obstructions.

Specifications and Operating Parameters

Flow: 1000-3,200 gallons/hour, Power: 6-30 watts,

Maximum Motor Temp: 50-60 degrees C

Aquarium Wall Thickness: 3/16” to 3/4”

Your VorTech propeller pump

Before you start

Preparation

Once you have chosen the location where you wish to install your VorTech pump, clean away any algae, calcified or

otherwise, using a razor blade.

Notes on placement

The VorTech creates over 3,200 gallons per hour of low velocity flow within your aquarium. Take care to place the

VorTech in a suitable location where corals are not directly in the line of flow. Place the pump sufficiently high enough

above a fine sand bed so that sand is not blown around by the output or undertow created by the VorTech.

Protect the pump from water

The VorTech’s motor housing and driver are NOT WATERPROOF. Any water allowed into these components can damage

them enough to require replacement. This kind of damage is NOT covered in the VorTech’s warranty. Protect these

components from splashes of any kind.

Adjust the pin spacer

The VorTech pump is designed to operate with a constant gap between both halves of

the device. The pin spacer is used to ensure the proper spacing for various aquarium wall

thicknesses.

Make sure to measure your aquarium’s glass thickness using a ruler or contact the aquari-•

um manufacturer in order to determine the exact thickness.

To adjust for the proper aquarium thickness, pull the pin spacer from the motor housing. •

Then align the VorTech’s power cord emerging from the motor with your aquarium’s wall

thickness to achieve the proper offset from your aquarium.

Note: 3/4” thick aquariums do not use the pin spacer at all.

IMPORTANT: When adjusting the pin spacer, be sure not to bend the pins as they are inserted into the

holes within the heat sink as this may permanently damage your VorTech. Bent pins WILL NOT be covered

under warranty.

1 2 3 4 5 6 7 8 9 10

Inhaltsverzeichnis

Seite 1 - Adjust the pin spacer

To remove the nozzle from the wet frame, remove the entire wet half of the pump from the aquarium and place it on a non-metallic surface. Gently but

Seite 2 - Align the VorTech

FCC and CE Warnings:Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accep

Seite 3 - Wave Motion Warning

The VorTech utilizes very powerful magnets and can cause severe personal injury.•NEVER connect the two halves of this device without a proper spacer

Seite 4 - Advanced Features

Wireless Wave Drivers are capable of controlling a VorTech pump in a variety of different ways. Out of the box, any MP40w model pump is capable of

Seite 5 - General Operational Modes

Advanced FeaturesStep 2) Press and hold Mode and Set to enter Setup. The LED will blink red/white/blueAfter programming Night Mode, the pump will

Seite 6 - Firmware Upgrade

Lagoon Random ModeWhen a pump is in Lagoon Random Mode, the dial is used to set the maximum operational speed, and the driver will automatically rando

Seite 7

During the firmware upgrade process, turn off all Wireless Wave Drivers within 20 feet of the two that you will be performing the upgrade process wi

Seite 8 - ErrorCodes:

A pump group consists of one master pump and at least one slave pump. There can only be one master pump per group which can include an unlimited numb

Seite 9 - Customer Support

Wear of the drive shaftThe VorTech pump features a wear component in the form of the drive shaft. This part is designed with a special engineering g

Seite 10 - FCC and CE Warnings:

WarrantyCustomer [email protected](610) 954-8480Sales inquiries please contact:[email protected](800) 785-0338EcoTech Marine warr

Kommentare zu diesen Handbüchern

Keine Kommentare

Ecotech-marine Gen 2 MP40 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Pumpen Ecotech-marine Gen 2 MP40 herunter. EcoTech Marine Gen 2 MP40 User Manual [it] [es] [en] [de] Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Pumpen Ecotech-marine Gen 2 MP40